能量之海

 找回密码
 立即注册
查看: 1639|回复: 3

涡流反重力技术由SCHAUBIEGER

[复制链接]
发表于 2017-7-14 20:10:31 | 显示全部楼层 |阅读模式
The Schauberger's Flying Saucer
"The Repulsin" Type B
By Jean-Louis Naudin
created on October 5th, 1999 - JLN Labs - Last update February 4th, 2001

In the Repulsin "type B" the vortex turbine has been improved for increasing the "Implosion Effect" and thus the lifting force, so you will find below apossible explanation about the working principle of "the Repulsin" type B flying saucer from Viktor Schauberger.
The enhanced vortex turbine increases significantly the "implosion" effect in the vortex chamber. This contributes to generate a stronger thrust than the centrifugal turbine used in the Repulsin type A. By means of a suction screw-impeller, which revolved from the outside towards the inside along a cycloid spiral space-curve, the same force is generated which creates twisters, cyclones, typhoons through the effect of suction.
In 1941 some models had been built, one of them had a diameter of 2.4 meters with a small and very fast electric motor. It climbed straight up into the air so suddenly that unfortunately it hit the workshop ceiling and crashed to the ground in pieces...
The implosion motor uses the suction forces of implosion, there is no heat barrier and no sound barrier, because with friction almost entirely lacking, no heat is generated. The air flows through the rotating air inlets placed in the middle and follows the gap between the double membranes (with the wave pattern), this creates a spiral contraction of the flowing medium and creates a vacuum which increases the suction pull.
The enhanced vortex turbine uses two flat membranes with concentric rills on it. A wave pattern has been set on the upper and on the lower membrane. The upper wave is slightly out of phase with the lower wave. The air flow passes through small cavities where the volume sometimes is bigger and sometimes smaller due to the difference in phase between the upper and the lower membrane. When the air passes differents cavities it starts to pulsate. The pulsations are directly depending of the angular speed of the disc, this push-pull action creates an harmonic pulsation of energy...
The upper membrane is fixed and the lower rotates at high speed. On the edge rim there are special shaped blades ( boomerang shaped blades ). There are 120 blades ( 3 degrees spaced ).
A vortex spiral in a fluid medium
When the air exits from the turbine at high speed, it follows the curved shape of the hull and increases also its speed while the gap decreases along its path.

楼主热帖
 楼主| 发表于 2017-7-14 20:11:13 | 显示全部楼层
The Schauberger's Flying Saucer

" The Repulsin "type A
By Jean-Louis Naudin
created on September 26th, 1999 - JLN Labs - Last update March 10, 2006

In this article, I have tried to give you a possible explanation about the working principle of "the Repulsin" flying saucer from Viktor Schauberger (1938-1957). This document is the synthesis of a fine analysis on pictures of real working devices, on Schauberger's researches in vortexes (implosion principle) and on some technical papers from Henri Coanda (1886-1972) and Bernouilli's principle.
An original picture of the "Repulsin" ( Above) : A flying model of a Schauberger in January 1940
This device has been built with copper and uses a very high speed motor for the main vortex turbine.
The Repulsin device is an Electro-Aero-Dynamic device (E.A.D.) and uses two effects :
  • The Coanda Effect, a pure Aerodynamic effect based on the Bernouilly's principle ( see the Coanda Saucer Test)
  • The ElectroDynamic effect : The high speed vortex in the vortex chamber produces an electric charges separation effect, called "the diamagnetic effect " by Schauberger.

These two effects combined create the so-called "implosion effect".
When the main electric engine is started, the Coanda effect begins to create a differential aerodynamic pressure between the outer and the inner surface of the primary hull. At a higher speed, the vortex chamber becomes a kind of high electrostatic generator due to the air particles in high speed motion acting as an electrical charges transporter. The "Repulsin" will begin to glow due to the strong ionization effect of the air. Now, we have all the ingredients for a continuous and strong Aether Flow along the main axis from the top to the bottom of the craft.....
The radial air pressure required for lifting 1kg with the Coanda Effect is about 1,4 kg/cm2
The Repulsin "Type A" details
(Above) Some pictures of the vortex turbine ( in red ), the vortex area is in the middle ( the vortex chamber has been removed ).
A front view of the "Repulsin" type A, the primary hull and the vortex chamber have been shown in transparent mode

发表于 2017-12-29 22:35:21 来自手机 | 显示全部楼层
看不懂,楼主翻译过来
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

小黑屋|手机版|Archiver|能量之海

GMT+8, 2018-4-25 04:39 , Processed in 0.286144 second(s), 28 queries .

Powered by Discuz! X3.3 Licensed

© 2001-2013 Comsenz Inc.. 技术支持 by 巅峰设计

快速回复 返回顶部 返回列表